Other Compatible Accessories

EN‑EL15c Rechargeable Li-ion Battery: EN‑EL15c batteries can be used with Nikon Z 5 digital cameras.

• EN‑EL15b/EN‑EL15a/EN‑EL15 batteries can also be used. Note, however, that fewer pictures can be taken on a single charge than with the EN‑EL15c (Battery Endurance).

MH‑25a Battery Charger: The MH‑25a can be used to recharge EN‑EL15c batteries.

MB-N10 Battery Pack: A battery pack for Nikon mirrorless cameras. Attached to the camera, it allows the use of two EN-EL15c rechargeable Li-ion batteries as a power source.

• EN-EL15b/EN-EL15a/EN-EL15 batteries can be used in place of the EN‑EL15c. The number of pictures that can be taken on a single charge (i.e., battery endurance) will however drop compared to the EN-EL15c (Battery Endurance).

• Batteries inserted in the MB-N10 will charge when an EH-7P charging AC adapter is connected to the MB-N10’s charging connector.

• See the manual supplied with the MB-N10 for information on connection and removal and for instructions on its use and care.

EH‑7P Charging AC Adapter: The EH‑7P can be used to charge batteries inserted in the camera.

• The battery will not charge while the camera is on.

• It cannot be used to charge EN‑EL15a/EN‑EL15 batteries.

• The charging AC adapter can be used to power the camera; to do so, select [Enable] for [USB power delivery] in the setup menu. For more information, see “USB Power Delivery” (USB Power Delivery).

EP‑5B Power Connector, EH‑5d/EH‑5c/EH‑5b AC Adapter: Use AC adapters to power the camera for extended periods.

• The EP‑5B is needed to connect the EH‑5d/EH‑5c/EH‑5b to the camera. See “Attaching a Power Connector and AC Adapter” (Attaching a Power Connector and AC Adapter) for details.

Neutral Color (NC) filters can be used to protect the lens.

Filters may cause ghosting when the subject is framed against a bright light, or when a bright light source is in the frame. Filters can be removed if ghosting occurs.

Matrix metering may not produce the desired results with filters with exposure factors (filter factors) over 1× (Y44, Y48, Y52, O56, R60, X0, X1, C‑PL, ND2S, ND4, ND4S, ND8, ND8S, ND400, A2, A12, B2, B8, B12); we suggest that [Center-weighted metering] be selected instead. See the filter manual for details.

Filters intended for special-effects photography may interfere with autofocus or the in-focus indicator (I).

UC‑E24 USB Cable: A USB cable with a type C connector for connection to the camera and a type A connector for connection to the USB device.

UC‑E25 USB Cable: A USB cable with two type C connectors.

For information on attaching, removing, maintaining, and using FTZ mount adapters, refer to the mount adapter manual.

ME‑1 Stereo Microphone: Connect the ME‑1 to the camera microphone jack to record stereo sound. Using an external microphone also reduces the chance of picking up equipment noise, such as the sounds produced during movie recording when focus is achieved using autofocus.

ME‑W1 Wireless Microphone: A wireless Bluetooth microphone. Use the ME‑W1 for off-camera recording.

WR-R10 Wireless Remote Controller/WR-T10 Wireless Remote Controller

• When a WR‑R10 wireless remote controller is attached to the accessory terminal, the camera can be controlled wirelessly using a WR‑T10 wireless remote controller.

• The WR‑R10 can also be used to control radio-controlled flash units.

• For synchronized release involving more than one camera, ready multiple cameras with paired WR‑R10 units attached.

• When connecting the WR‑R10, be sure the cover for the accessory terminal and the USB and HDMI connectors is fully open.

WR‑1 Wireless Remote Controller: WR‑1 units are used with WR‑R10 or WR‑T10 wireless remote controllers or with other WR‑1 remote controllers, with the WR‑1 units functioning as either transmitters or receivers. When a WR‑R10 or a WR‑1 configured as a receiver is connected to the camera accessory terminal, a second WR‑1 configured as a transmitter can be used to take pictures and adjust camera settings remotely.

• Be sure the firmware for the WR‑R10 and WR‑1 has been updated to the latest versions (WR‑R10 firmware version 3.0 or later and WR‑1 firmware version 1.0.1 or later). For information on firmware updates, see the Nikon website for your area. Consult a Nikon-authorized service representative when updating the firmware for the WR‑R10 from versions prior to version 2.0 to version 3.0 or later.