Take photographs at the selected interval until the specified number of shots has been recorded. When using the interval timer, select a release mode other than E.
|
Option |
Description |
|---|---|
|
[] |
Start interval timer shooting. Shooting will begin either after 3 s ([] selected for []) or at a selected date and time ([]). Shooting will continue at the selected interval until all shots have been taken. |
|
[] |
Choose a start option. Select [] to start shooting immediately, [] to start shooting at a chosen date and time. |
|
[] |
Specify the interval between shots in hours, minutes, and seconds. |
|
[] |
Choose the number of intervals and the number of shots per interval. |
|
[] |
Selecting [] allows the camera to adjust exposure to match the previous shot.
|
|
[] |
Select [] to silence the shutter and eliminate the vibrations it produces during shooting.
|
|
[] |
|
|
[] |
If [] is selected, the camera will focus between shots. |
|
[] |
Combine interval-timer photography with other options.
|
|
[] |
Highlight either of the following options and press 2 to select; selected items are marked with a check (M). To deselect (remove the check from: U) a selected option, highlight it and press 2 again.
|
Interval-Timer Photography
-
Take a test shot at current settings.
-
Before proceeding, select [] in the setup menu and make sure that the camera clock is set to the correct time and date.
-
To ensure that shooting is not interrupted, use a fully-charged battery, an optional charging AC adapter, or an optional AC adapter and power connector.
-
Highlight [] in the photo shooting menu and press 2.
-
Adjust interval timer settings.
-
Choose the start day and time.
Highlight [] and press 2.
Highlight an option and press J.
-
To start shooting immediately, select [].
-
To start shooting at a chosen date and time, select []. Choose the date and time and press J.
-
-
Choose the interval between shots.
Highlight [] and press 2.
Choose an interval (in hours, minutes, and seconds) and press J.
-
Choose the number of shots per interval.
Highlight [] and press 2.
Choose the number of intervals and the number of shots per interval and press J.
-
In single frame release mode, the photographs for each interval will be taken at the rate for continuous high-speed release mode.
-
When [] is selected for [], the maximum number of intervals will vary with the number of shots per interval.
-
-
Enable or disable exposure smoothing.
Highlight [] and press 2.
Highlight an option and press J.
-
Selecting [] allows the camera to adjust exposure to match the previous shot.
-
-
Enable or disable silent photography.
Highlight [] and press 2.
Highlight an option and press J.
-
Choose an interval priority option.
Highlight [] and press 2.
Highlight an option and press J.
-
Choose whether the camera focuses between shots.
Highlight [] and press 2.
Highlight an option and press J.
-
Choose additional options.
Highlight [] and press 2.
Highlight [] or [] and press J.
-
If you selected [], choose values for [] and []; if you selected [], choose settings for [] and [].
-
-
Choose starting folder options.
Highlight [] and press 2.
Select the desired options and press J to proceed.
-
-
Highlight [] and press J.
-
If [] was selected for [] in Step 2, shooting will start after three seconds.
-
Otherwise shooting will start at the time selected for [] > [].
-
The display turns off during shooting.
-
Shooting will continue at the selected interval until all shots have been taken.
-
-
During interval timer photography, the memory card access lamp will flash.
-
If the display is turned on by pressing the shutter-release button halfway, the message [] will be displayed and the Q icon will flash.
Pausing Interval-Timer Photography
Interval-timer photography can be paused between intervals by pressing J or by selecting [] in the photo shooting menu, highlighting [], and pressing J. Note that the menus may not be displayed when the G button is pressed if the time selected for [] is very short.
-
If [] is selected for [], pressing J between intervals will end interval-timer photography.
Resuming Interval Timer Shooting
Interval timer shooting can be resumed as described below.
-
To resume shooting immediately:
Highlight [] and press J.
-
To resume shooting at a specified time:
Highlight [] and press 2, then highlight [] and press 2.
Choose a starting date and time and press J.
Highlight [] and press J.
Ending Interval Timer Shooting
To end interval-timer photography before all the photos are taken, select [] in the photo shooting menu, highlight [], and press J. Note that the menus may not be displayed when the G button is pressed if the time selected for [] is very short. In this case you will need to press J to pause interval-timer photography and then select [] in the photo shooting menu, highlight [], and press J.
-
Choose an interval longer than the time needed to take the selected number of shots at the predicted shutter speed. Note that during actual interval-timer photography, the camera must not only take shots at the selected interval but must also have sufficient time to complete the exposures and perform such tasks as processing the photographs. If the interval is too short to take the selected number of photos, the camera may skip to the next interval without shooting.
-
If the interval is too short, the total number of shots taken may be less than that selected for [].
-
If you are using a flash, choose an interval longer than the time needed for the flash to charge. If the interval is too short, the flash may fire at less than the power needed for full exposure.
-
If shooting cannot proceed at current settings—for example, if shutter speed is set to “Bulb” or “Time”, the [] is [], or the start time is in less than a minute—a warning will be displayed in the monitor.
-
Interval-timer photography will not start if [] is selected for both [] and [] and [] is selected for [].
-
In the case of the Z 7II, interval-timer photography will not start if all options are set as described below. To record a time-lapse movie under these conditions, use [] in the photo shooting menu. Note that in this case, the individual frames will not be recorded separately.
-
[]: []
-
[]: []
-
[]: []
-
-
If [] is selected for [] or [] is selected for [], the standby timer will not expire during interval-timer photography, regardless of the option selected for Custom Setting c3 [] > [].
-
If the memory card is full, the interval timer will remain active but no pictures will be taken. Insert another memory card and resume shooting (Pausing Interval-Timer Photography).
-
Depending on memory card performance and shooting conditions, shooting may end before the selected number of shots have been taken or the selected number of intervals is complete.
-
Interval timer shooting will pause if:
-
The camera is turned off and then on again (when the camera is off, batteries and memory cards can be replaced without ending interval-timer photography)
-
E is selected for release mode
-
-
Changing camera settings while the interval timer is active may cause shooting to end.
Regardless of the release mode selected, the camera will take the specified number of shots at each interval.
Pictures can be viewed and shooting and menu settings adjusted between shots. Note, however, that the monitor will turn off and shooting will resume a few seconds before the next shot is taken.
Interval-timer photography cannot be combined with some camera features, including:
-
movie recording,
-
long time-exposures (“Bulb” or “Time”),
-
the self-timer,
-
bracketing,
-
HDR (high dynamic range),
-
multiple exposures, and
-
focus shift
Selecting [] for [] disables some camera features, including:
-
ISO sensitivities of Hi 0.3 through Hi 2.0,
-
flash photography,
-
long-exposure noise reduction, and
-
flicker reduction.
Turning the camera off or selecting a new release mode does not affect interval-timer photography settings.